General method, not a substitute for your manual. Fluid types, belt specs and any torque values are specific to your engine, drive and boat. Check the service manual for your engine's serial for those numbers; this guide covers the method and what to look for.
Hull and running gear
- Inspect the bottom for blisters, cracks or soft spots
- Check anodes and replace any that are significantly wasted; freshwater boats need magnesium anodes, not the zinc or aluminum used in salt water
- Check the prop for dings and the shaft for straightness
- Check cutless bearing play and exercise thru-hulls and seacocks so they aren't seized
Engine fluids
- Confirm oil was changed in the fall, or change it now if it wasn't
- Check coolant level and condition on closed-cooled engines
- Check gear lube level and look for a milky or cloudy appearance, a sign of water intrusion; see the milky gear lube guide
- Check belt tension and look for cracking or glazing
Raw-water cooling
- Install a new impeller if it wasn't done in the fall
- Open the seacock and confirm it moves freely
- Check that the raw-water strainer is clean and clear
Fuel
- Check for water or phase-separated fuel in the tank
- Replace fuel filters and water separators
- Inspect fuel hoses and clamps for cracking or corrosion
Batteries
- Reinstall and fully charge the battery or battery bank
- Clean and protect terminals
- Test the battery under load rather than assuming a charged battery is a good battery
Steering and controls
- Check full travel of the wheel or tiller with no binding
- Check hydraulic steering fluid level if applicable
- Grease steering and control cable fittings
Safety gear
- Check that flares are in date and extinguishers are charged and tagged
- Confirm PFDs are on board and in good condition
- Test bilge pumps and float switches
- Confirm nav lights work
Plumbing
- Flush antifreeze out of the fresh water system
- Test the head and its pumps
Launch and sea trial
After launch, confirm cooling (water flow and normal temperature), charging voltage with the engine running, correct shifting in both directions, steering with no binding, and a dry bilge. A sea trial is what turns a fluid-and-inspection checklist into an actual confirmation that the boat is ready, not just that it was reassembled correctly.
Why the inspection matters more than the checklist itself: most of spring commissioning is straightforward, reversing what winterizing did. The value is in what gets caught along the way, before it becomes a problem out on Lake St. Clair instead of at the dock.
Work through it in an order that makes sense
It helps to move from the outside of the boat inward: hull and running gear first while the boat may still be on a rack or trailer and easy to walk around, then engine fluids and raw-water cooling before anything is asked to run, then fuel and batteries so the engine has what it needs to actually start, and steering, safety gear and plumbing last before launch. Doing it out of order is not wrong, but working front to back like this means you are not double-checking something you already covered, and nothing gets skipped because it was assumed to be handled by an earlier step.
Why this list is longer than "just start the engine"
A boat that sat all winter has more going on than one engine. Anodes wasted more than expected, a seacock that seized from disuse, a belt that glazed sitting under tension, or a battery that slowly lost charge over the off season are all things a straight startup attempt will not catch until they cause a problem on the water. Working the full list, even the parts that feel like they probably didn't change, is what catches the one thing that actually did.
If commissioning turns something up
Milky gear lube, a stiff seacock, a worn cutless bearing or a glazed belt are common finds during commissioning. None of these are reasons to delay launch on their own, but each is worth a decision rather than being ignored. See spring commissioning for the full service, or boat detailing if the boat needs a compound and polish to look its best for the season alongside the mechanical work.
Doing your own commissioning versus having it done
Most of this checklist is within reach for an owner comfortable with basic engine and hull maintenance. Where it gets harder is knowing what counts as normal wear versus something worth flagging, a slightly worn cutless bearing versus one that actually needs replacing, or a belt that looks fine but is one season from cracking. That judgment call, more than the individual steps, is where having someone who does this full time pays off.
Want it on paper? The Bilge & Bench Spring Commissioning Checklist + Sea Trial Log is a printable checklist Brad wrote from real dock calls. For background on each system, see the marine knowledge base.
Get on the spring launch list
Text the year, make and engine, or a photo of the engine, and your launch date.
