Skip to content

Home / Guides / Shrink wrap prep

DIY guide · Lake St. Clair

What to do before your boat is shrink wrapped

Shrink wrap protects the boat from snow and rain, but it also seals moisture inside if the boat wasn't ready first. Work through this before the wrap crew shows up.

Note: this guide covers getting the boat ready before it's wrapped. Brad does not do the shrink wrapping itself; he winterizes the boat so it's actually ready for whoever wraps it.

Winterize before you wrap, not after

Shrink wrap is a cover, not a preservation step. It keeps snow and rain off the boat, but it does nothing for the engine, drive, fresh water system or fuel. If the boat is wrapped before it's winterized, all shrink wrap does is hide a boat that's about to freeze inside a sealed tent. Winterizing, oil and filter changes, draining or antifreezing the raw-water side, fuel stabilizing, and gear lube service, needs to happen first. See boat winterization for what that covers.

Vents matter more than most owners expect

A shrink wrap job should include vents, small openings built into the wrap that let air move in and out of the covered space. Without them, a sealed wrap traps warm, moist air inside on any sunny winter day, and that moisture condenses on cold surfaces overnight. Confirm with whoever is wrapping the boat that vents are part of the job, and that they haven't been taped over or blocked once the wrap goes on.

Disconnect or remove the battery first

The battery should be fully charged and either disconnected or pulled entirely before the boat is wrapped, the same as for any winterization layup. A battery left connected can draw down slowly over the winter from small parasitic loads, and a battery that's already low going into a hard freeze is more likely to be damaged by the cold.

Take the canvas and electronics off first

Canvas, cushions, electronics and anything else that doesn't need to spend the winter under plastic should come off the boat before it's wrapped, not left inside hoping the wrap protects it. Trapped moisture under shrink wrap is harder on fabric and electronics than open winter air is. Portable electronics, cushions and canvas stored dry indoors come back out in spring in far better shape than anything left sealed up all winter.

A dry bilge before the wrap goes on

Pump the bilge dry and leave it dry before the boat is covered. Any standing water left in the bilge over a Michigan winter is water that can freeze, and a sealed shrink wrap tent does not evaporate it away, it just holds the moisture in with nowhere to go. A dry bilge going into the wrap is a dry bilge coming out of it in spring.

Don't let the wrap trap moisture in general

The theme across all of this is the same: shrink wrap holds in whatever is under it, moisture included. A boat that's winterized, vented, dry in the bilge, and cleared of anything that shouldn't sit sealed up for months comes out from under the wrap in spring in much better shape than one that was wrapped wet, closed up tight, and left to condense all winter.

What Brad actually does here

Brad winterizes the boat itself, engine, drive, fuel, fresh water and batteries, so it's genuinely ready before it goes under wrap, whether the wrapping itself is done by a marina, a canvas shop, or another contractor. See boat winterization for the full scope, or marine electrical if the battery or wiring needs attention before it's disconnected for the season.

Looking for the full outboard winterizing steps instead of the general shrink wrap checklist? See how to winterize an outboard. General reference material on marine systems is also in the site's marine knowledge base.

A quick pre-wrap walk-through

Before the wrap crew arrives, a short walk around the boat catches most of what matters: engine and drive winterized, battery charged and disconnected, canvas and electronics removed, bilge pumped dry, and any hatch or locker that tends to hold moisture left open rather than sealed shut under the wrap. It takes a few minutes and it is the difference between a boat that comes out from under the wrap in spring the way it went in, and one that comes out damp, musty, or worse.

Want it on paper? The Bilge & Bench Haul-Out Day Checklist + Storage Prep is a printable checklist Brad wrote from real dock calls. For background on each system, see the marine knowledge base.

Get the boat actually ready for winter

Text a photo of the engine and your haul or wrap date.