Every outboard is a little different. This is the general method. Your engine's own owner's manual has the specific steps, fluids and any exceptions for your model and serial, and takes priority over a general guide whenever the two disagree.
Fuel first
Old fuel, especially ethanol gas that's sat all season, is one of the most common causes of a rough start or no-start in spring. Add fuel stabilizer to the tank and run the engine long enough to circulate treated fuel through the whole system rather than just the tank. If the boat won't be run again before storage, stabilizing what's already in the tank and lines is still worth doing.
Fogging protects the cylinders
Many outboard makers call for fogging oil to be introduced into the cylinders near the end of the last run, coating the internals against corrosion over the storage months. Follow your engine maker's fogging procedure, since the method (through the carburetor, an air intake, or a dedicated port) varies by engine.
Gear lube and the milky-lube check
Change the lower unit gear lube as part of winterizing, and pay attention to what comes out. Clear gear lube going out and clear gear lube going back in is normal. Milky, cloudy or water-streaked gear lube means water has gotten past a seal somewhere in the lower unit, and that's worth having looked at rather than just refilling and hoping it was a one-time thing. See the milky gear lube guide for what that actually means.
Trim down to drain the lower unit
Trim the outboard all the way down before it goes into winter storage so that any water in the gearcase and exhaust passages can drain out rather than sitting and freezing. An outboard stored trimmed up can hold water in places that a hard freeze will crack.
Flush the cooling system
A final freshwater flush clears salt, minerals and debris from the raw-water cooling passages before the engine sits all winter. This is worth doing even on a freshwater lake like Lake St. Clair, since mineral buildup happens in fresh water too, just more slowly than in salt water.
2-stroke and 4-stroke need different attention
A 4-stroke outboard has its own crankcase oil, separate from fuel, and that oil should be changed as part of winterizing the same as any other engine. A 2-stroke burns oil rather than holding a crankcase supply, either premixed with the fuel or injected separately, so its winterizing steps focus more on the fuel and injection oil system than on a crankcase oil change.
Battery and general layup
Charge the battery fully and either disconnect it or bring it inside for the winter. A battery left connected at low charge through a Michigan winter is more likely to be damaged by the cold than one that's disconnected or removed.
Small tender and dinghy outboards need the same care
A small outboard on a dinghy or tender is easy to treat as an afterthought next to the main engine, but it goes through the same fuel, gear lube and drainage steps as any other outboard. Fuel stabilizing, a gear lube change with a milky-lube check, fogging, and trimming down to drain the gearcase all apply just the same to a small tender motor that only ran a handful of times all season.
What Brad checks that a checklist alone won't catch
The written steps above cover the method, but the judgment call is in what the gear lube and the fuel actually look like when they come out, not just whether the steps were followed. A slightly milky lube, a fuel filter with more debris than expected, or a water pump that already feels marginal are the kind of things worth flagging for spring rather than waiting to discover them when the engine won't cooperate at the start of the season.
If it feels like more than a DIY afternoon
None of this is complicated on its own, but it adds up, and a missed step, especially the gear lube or the trim-down drain, can cost far more than the winterizing itself would have. See boat winterization if you'd rather have it done and confirmed, or outboard repair if something already seems off before you even get to winterizing it.
Getting the boat wrapped for the season too? See the shrink wrap prep checklist for what to do after winterizing and before the wrap goes on.
Want it on paper? The Bilge & Bench Freshwater Winterization Checklist is a printable checklist Brad wrote from real dock calls. For background on each system, see the marine knowledge base.
Skip the DIY and get it booked
Text the year, make and horsepower of your outboard, and your haul date.
